28 RPM to Radians Per Second Converter
Instant conversion for 28 RPM to rad/s (2.932153 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 2.9321531
- Degrees per Second (°/s)
- 168 °/s
- Hertz (Hz)
- 0.466667 Hz
- Revolutions per Second (RPS)
- 0.466667 rev/s
- Revolutions per Hour (RPH)
- 1,680 rev/hr
- Revolutions per Day
- 40,320 rev/day
- Radians per Minute (rad/min)
- 175.92919 rad/min
- Milliradians per Second (mrad/s)
- 2,932.1531 mrad/s
- Period (seconds per rev)
- 2.142857 s/rev
- Exact Formula
- 28 × π/30 = 2.9321531 rad/s
- Nearest Real-World Example
- Ceiling fan — high (200 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 28 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 28 × (π / 30) = 2.932153 rad/s
Exact fraction: 28π/30 rad/s · Reciprocal: 2.932 rad/s × (30/π) = 28 RPM
Reverse Conversion: 2.932 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
28 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
28 RPM = 14π/15 rad/s ≈ 2.932153 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 2.9316 rad/s instead of the exact 2.9322 rad/s — an error of 0.0005531 rad/s.
What this speed looks like in practice
At 28 RPM a shaft turns about 1.87× as fast as a utility-scale wind turbine rotor. An LP record (33⅓ RPM) turns about 1.19× faster.
Revolutions over time
That is 1,680 revolutions per hour and 40,320 per day. A quarter turn (90°) takes 536 ms, and the shaft sweeps 0.168° every millisecond.
Rim speed and centripetal load at ω = 2.9322 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 0.02932 m/s · 0.1056 km/h | 0.08598 m/s² · 0.008767 g |
| 5 cm | 10 cm | 0.1466 m/s · 0.5278 km/h | 0.4299 m/s² · 0.04384 g |
| 10 cm | 20 cm | 0.2932 m/s · 1.056 km/h | 0.8598 m/s² · 0.08767 g |
| 25 cm | 50 cm | 0.733 m/s · 2.639 km/h | 2.149 m/s² · 0.2192 g |
| 50 cm | 1 m | 1.466 m/s · 5.278 km/h | 4.299 m/s² · 0.4384 g |
| 1 m | 2 m | 2.932 m/s · 10.56 km/h | 8.598 m/s² · 0.8767 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 28 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 0.4667 Hz | Below typical VFD range — use a gearbox |
| 4 | 0.9333 Hz | Below typical VFD range — use a gearbox |
| 6 | 1.4 Hz | Below typical VFD range — use a gearbox |
| 8 | 1.867 Hz | Below typical VFD range — use a gearbox |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 9.333 RPM · 0.9774 rad/s | ×3 |
| 5:1 | 5.6 RPM · 0.5864 rad/s | ×5 |
| 10:1 | 2.8 RPM · 0.2932 rad/s | ×10 |
| 30:1 | 0.9333 RPM · 0.09774 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 0.004299 J |
| 0.01 kg·m² (bench-grinder wheel) | 0.04299 J |
| 0.1 kg·m² (car flywheel) | 0.4299 J |
| 1 kg·m² (industrial flywheel) | 4.299 J |
Multiples of this speed
- 0.5× = 14 RPM1.4661 rad/s
- 2× = 56 RPM5.8643 rad/s
- 5× = 140 RPM14.6608 rad/s
- 10× = 280 RPM29.3215 rad/s

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 28 RPM to radians per second, multiply 28 by π and divide by 30: 28 × (π / 30) = 2.932153 rad/s (approx. 2.932 rad/s).
28 RPM equals 0.4667 Hz (revolutions per second), calculated by dividing 28 by 60 seconds.
To convert 2.932 rad/s back to RPM, multiply by 30 and divide by π: 2.932 × (30 / π) ≈ 28 RPM.
At 28 RPM, one full 360° revolution takes 2.1429 seconds (2142.86 ms).
A 4-pole induction motor has a synchronous speed of 28 RPM at 0.9333 Hz (f = RPM × poles / 120 = 28 × 4 / 120). That is far below a drive's usable range, so in practice a standard motor runs faster and a gearbox or gearmotor brings the output down to this speed.
Tangential speed is v = ω·r = 2.932153 rad/s × 0.1 m = 0.2932 m/s (1.0556 km/h). The centripetal acceleration at the rim is ω²·r = 0.8598 m/s².