RPM to Radians Per SecondRPM to rad/s

SFM to RPM Calculator (Cutting Speed to Spindle Speed)

Enter a cutting speed and the tool or workpiece diameter to get spindle RPM, or go the other way. It works in imperial (SFM, inches) or metric (m/min, mm), has starting speeds for common materials, and turns chip load into a feed rate.

Machining

Cutting speed ↔ spindle RPM

For turning use the workpiece diameter; for milling and drilling use the tool diameter.

SFM
in
Starting speeds:

Feed rate (optional, milling/drilling)

in/tooth
Spindle speed
3,820RPM
Spindle speed3,819.72 RPM
Cutting speed500 SFM · 152.4 m/min
ω400 rad/s
Feed rate30.5577 in/min
Show the working
  1. RPM = 12 × SFM / (π × D)
  2. = 12 × 500 / (π × 0.5 in)
  3. = 3,819.72 RPM (shop rule 3.82 × SFM / D ≈ 3,820)
  4. F = n × z × fz = 3,819.72 × 4 × 0.002 = 30.5577 in/min
Material speeds are conservative starting points. Follow the tool maker's data and adjust for rigidity, coolant and tool life.

SFM to RPM formula

Cutting speed is the surface speed at the cutting edge: how many feet (or metres) of material pass the edge every minute. One revolution moves a point on the circumference π × D, so speed = π × D × RPM. Solving for RPM and fixing the units gives:

RPM = (12 × SFM) / (π × D_in) ≈ 3.82 × SFM / DSFM = π × D_in × RPM / 12 ≈ 0.262 × D × RPMn = (1000 × Vc) / (π × D_mm)Vc = π × D_mm × n / 1000

The 12 converts feet to inches and the 1000 converts metres to millimetres. 3.82 is just 12/π rounded; the calculator uses the exact value, which matters for small diameters at high SFM.

Cutting speed is linear velocity, so this is the same physics as v = ω × r with machining units. The spindle's angular velocity in rad/s is shown in the result for anyone sizing a spindle drive with the torque and power calculator.

Worked examples

  1. Turning mild steel with carbide. Workpiece Ø 2.0 in, 500 SFM. RPM = 12 × 500 / (π × 2) = 955 RPM.
  2. Milling aluminium. 12 mm 3-flute carbide end mill at 300 m/min. n = 1000 × 300 / (π × 12) = 7958 RPM. At fz = 0.05 mm, feed = 7958 × 3 × 0.05 = 1194 mm/min.
  3. Drilling stainless with HSS. ¼ in drill (0.25 in), 60 SFM. RPM = 12 × 60 / (π × 0.25) = 917 RPM.
  4. Checking a spindle limit. A 6 in face mill at 6000 RPM runs π × 6 × 6000 / 12 = 9425 SFM, far above any carbide grade for steel. Reduce speed or use a smaller cutter.

Cutting speeds by material

Typical starting ranges for turning and milling. Drilling usually runs 60–70% of these speeds. Always check the insert or tool manufacturer's recommendation.

Starting cutting speeds (SFM | m/min)
MaterialHSS (SFM)Carbide (SFM)HSS (m/min)Carbide (m/min)
Aluminium alloys400–800800–1500120–245245–460
Brass, bronze200–350500–90060–105150–275
Mild steel (1018)80–120350–65025–37105–200
Alloy steel (4140)50–80250–45015–2575–135
Stainless (304)40–80200–40012–2560–120
Cast iron (grey)60–100250–45018–3075–135
Titanium (Ti-6Al-4V)30–50100–2009–1530–60
Plastics (acetal, nylon)300–600500–100090–180150–300

Spindle RPM quick chart

RPM by diameter and SFM
Diameter100 SFM300 SFM500 SFM800 SFM
1/8 in305691671527924446
1/4 in15284584763912223
1/2 in764229238206112
3/4 in509152825464074
1 in382114619103056
2 in1915739551528
4 in95286477764

Common mistakes

  • Using radius instead of diameter. The formulas use D. Using the radius doubles the RPM.
  • Using the tool diameter on a lathe. In turning, the diameter is the workpiece's, and it shrinks as you cut. CNC lathes with constant surface speed (G96) recalculate RPM continuously for this reason.
  • Mixing SFM and m/min. 300 m/min is 984 SFM, so entering m/min into an SFM formula runs the tool about three times too slow.
  • Ignoring the spindle maximum. Small cutters often ask for more RPM than the machine has. Cap the RPM and recalculate the feed from the RPM you can actually run.

Frequently asked questions

How do you convert SFM to RPM?

RPM = 12 × SFM ÷ (π × diameter in inches), or approximately 3.82 × SFM ÷ D. For 400 SFM and a 0.5 in cutter: 3.82 × 400 / 0.5 ≈ 3056 RPM.

What does SFM mean?

Surface feet per minute: the speed, in feet per minute, at which the material moves past the cutting edge. It is the imperial name for cutting speed.

How do you convert m/min to RPM?

n = 1000 × Vc ÷ (π × D), with Vc in metres per minute and D in millimetres. 150 m/min with a 20 mm tool gives 2387 RPM.

Why is the number 3.82 used in the RPM formula?

3.82 is 12 ÷ π rounded. The 12 converts feet to inches and π converts diameter to circumference.

How do I calculate milling feed rate?

Feed rate = RPM × number of flutes × chip load per tooth. 5000 RPM × 4 flutes × 0.002 in = 40 in/min.

Should I use workpiece or tool diameter?

Use the diameter of whatever is rotating at the cut: the workpiece on a lathe, the cutter on a mill or drill press.

Terms used on this page

SFM
Surface feet per minute; imperial cutting speed.
Vc (cutting speed)
Speed of the material past the cutting edge, in m/min in metric practice.
Spindle speed (n)
Rotational speed of the spindle in RPM (min⁻¹).
Chip load (fz)
Thickness of material each tooth removes per revolution, in in/tooth or mm/tooth.
Feed rate (F, vf)
Linear speed of the tool through the work, in in/min or mm/min.
Constant surface speed (CSS)
Lathe mode (G96) that changes RPM as diameter changes to hold SFM constant.

Further reading