30 RPM to Radians Per Second Converter
Instant conversion for 30 RPM to rad/s (3.141593 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 3.1415927
- Degrees per Second (°/s)
- 180 °/s
- Hertz (Hz)
- 0.5 Hz
- Revolutions per Second (RPS)
- 0.5 rev/s
- Revolutions per Hour (RPH)
- 1,800 rev/hr
- Revolutions per Day
- 43,200 rev/day
- Radians per Minute (rad/min)
- 188.49556 rad/min
- Milliradians per Second (mrad/s)
- 3,141.5927 mrad/s
- Period (seconds per rev)
- 2 s/rev
- Exact Formula
- 30 × π/30 = 3.1415927 rad/s
- Nearest Real-World Example
- Ceiling fan — high (200 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 30 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 30 × (π / 30) = 3.141593 rad/s
Exact fraction: 30π/30 rad/s · Reciprocal: 3.142 rad/s × (30/π) = 30 RPM
Reverse Conversion: 3.142 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
30 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
30 RPM = π rad/s ≈ 3.141593 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 3.141 rad/s instead of the exact 3.1416 rad/s — an error of 0.0005927 rad/s.
What this speed looks like in practice
At 30 RPM a shaft turns about 2× as fast as a utility-scale wind turbine rotor. An LP record (33⅓ RPM) turns about 1.11× faster.
Revolutions over time
That is 1,800 revolutions per hour and 43,200 per day. A quarter turn (90°) takes 500 ms, and the shaft sweeps 0.18° every millisecond.
Rim speed and centripetal load at ω = 3.1416 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 0.03142 m/s · 0.1131 km/h | 0.0987 m/s² · 0.01006 g |
| 5 cm | 10 cm | 0.1571 m/s · 0.5655 km/h | 0.4935 m/s² · 0.05032 g |
| 10 cm | 20 cm | 0.3142 m/s · 1.131 km/h | 0.987 m/s² · 0.1006 g |
| 25 cm | 50 cm | 0.7854 m/s · 2.827 km/h | 2.467 m/s² · 0.2516 g |
| 50 cm | 1 m | 1.571 m/s · 5.655 km/h | 4.935 m/s² · 0.5032 g |
| 1 m | 2 m | 3.142 m/s · 11.31 km/h | 9.87 m/s² · 1.006 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 30 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 0.5 Hz | Below typical VFD range — use a gearbox |
| 4 | 1 Hz | Below typical VFD range — use a gearbox |
| 6 | 1.5 Hz | Below typical VFD range — use a gearbox |
| 8 | 2 Hz | Below typical VFD range — use a gearbox |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 10 RPM · 1.047 rad/s | ×3 |
| 5:1 | 6 RPM · 0.6283 rad/s | ×5 |
| 10:1 | 3 RPM · 0.3142 rad/s | ×10 |
| 30:1 | 1 RPM · 0.1047 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 0.004935 J |
| 0.01 kg·m² (bench-grinder wheel) | 0.04935 J |
| 0.1 kg·m² (car flywheel) | 0.4935 J |
| 1 kg·m² (industrial flywheel) | 4.935 J |
Multiples of this speed

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 30 RPM to radians per second, multiply 30 by π and divide by 30: 30 × (π / 30) = 3.141593 rad/s (approx. 3.142 rad/s).
30 RPM equals 0.5000 Hz (revolutions per second), calculated by dividing 30 by 60 seconds.
To convert 3.142 rad/s back to RPM, multiply by 30 and divide by π: 3.142 × (30 / π) ≈ 30 RPM.
At 30 RPM, one full 360° revolution takes 2 seconds (2000.00 ms).
A 4-pole induction motor has a synchronous speed of 30 RPM at 1 Hz (f = RPM × poles / 120 = 30 × 4 / 120). That is far below a drive's usable range, so in practice a standard motor runs faster and a gearbox or gearmotor brings the output down to this speed.
Tangential speed is v = ω·r = 3.141593 rad/s × 0.1 m = 0.3142 m/s (1.131 km/h). The centripetal acceleration at the rim is ω²·r = 0.987 m/s².