RPM to Radians Per SecondRPM to rad/s

600 RPM to Radians Per Second Converter

Instant conversion for 600 RPM to rad/s (62.831853 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.

m
Result62.831853 rad/s
Radians per Second (rad/s)
62.831853
Degrees per Second (°/s)
3,600 °/s
Hertz (Hz)
10 Hz
Revolutions per Second (RPS)
10 rev/s
Revolutions per Hour (RPH)
36,000 rev/hr
Revolutions per Day
864,000 rev/day
Radians per Minute (rad/min)
3,769.9112 rad/min
Milliradians per Second (mrad/s)
62,831.853 mrad/s
Period (seconds per rev)
0.1 s/rev
Exact Formula
600 × π/30 = 62.831853 rad/s
Nearest Real-World Example
Car engine — idle (800 RPM)
Precision Drift Meter (Exact π/30 vs. 0.10472 Rounded)Zero Drift Here

Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:

Exact Value (π/30):62.831853 rad/s
Rounded (0.10472):62.832000 rad/s
Angular Error / Hour:30.31° / hr

Worked Conversion: 600 RPM to Radians Per Second

To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.

rad/s = 600 × (π / 30) = 62.831853 rad/s

Exact fraction: 600π/30 rad/s · Reciprocal: 62.832 rad/s × (30/π) = 600 RPM

Angular Velocity
62.831853 rad/s
Frequency
10 Hz
Degrees / Second
3,600 °/s
Period per Rev
0.1 s
Engineering Context: The high hundreds of RPM is where kitchen appliances and idling engines sit, and where angular velocity starts to dominate the mechanical design.

Reverse Conversion: 62.832 rad/s to RPM

Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.

Browse Reverse Conversions →

In-Depth Engineering Guides & References

5.36 Rad/s to RPM: College Physics Homework Benchmark Solution— Serway & Halliday kinematics proof and analytical derivation.
RPM to Radians Per Second Formula & Calculus Proof— Dimensional cancellation, π/30 derivation, and IEEE 754 precision.
Standard Motor RPMs: Synchronous Speeds & Slip— 50 Hz vs 60 Hz grids, pole counts, and synchronous motor speeds.
Angular Velocity Guide & Rotational Kinematics— SI standards, tangential velocity (v = ω·r), and centripetal acceleration.
Complete Conversion Index— Browse pre-calculated conversion speeds from 1 to 20,000 RPM.

600 RPM: exact form, real-world scale & engineering tables

Exact answer in terms of π

600 RPM = 20π rad/s ≈ 62.831853 rad/s

Reduced fraction — keep this form through multi-step problems and only round at the end.

Rounding check

Using the rounded factor 0.1047 gives 62.82 rad/s instead of the exact 62.8319 rad/s — an error of 0.01185 rad/s.

What this speed looks like in practice

At 600 RPM a shaft turns about 3× as fast as a ceiling fan on high. A car engine at idle turns about 1.25× faster.

Revolutions over time

That is 36,000 revolutions per hour and 864,000 per day. A quarter turn (90°) takes 25 ms, and the shaft sweeps 3.6° every millisecond.

Rim speed and centripetal load at ω = 62.8319 rad/s

Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.

RadiusDiameterRim speedCentripetal acceleration
1 cm2 cm0.6283 m/s · 2.262 km/h39.48 m/s² · 4.026 g
5 cm10 cm3.142 m/s · 11.31 km/h197.4 m/s² · 20.13 g
10 cm20 cm6.283 m/s · 22.62 km/h394.8 m/s² · 40.26 g
25 cm50 cm15.71 m/s · 56.55 km/h987 m/s² · 100.6 g
50 cm1 m31.42 m/s · 113.1 km/h1,974 m/s² · 201.3 g
1 m2 m62.83 m/s · 226.2 km/h3,948 m/s² · 402.6 g

Driving this speed with an AC motor

Supply frequency an induction motor would need for a synchronous speed of 600 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.

PolesSupply frequencyPractical note
210 HzReachable with a VFD
420 HzReachable with a VFD
630 HzReachable with a VFD
840 HzReachable with a VFD

Through a reduction gearbox

Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.

RatioOutput speedTorque ×
3:1200 RPM · 20.94 rad/s×3
5:1120 RPM · 12.57 rad/s×5
10:160 RPM · 6.283 rad/s×10
30:120 RPM · 2.094 rad/s×30

Stored rotational energy

Kinetic energy E = ½·I·ω² for a range of moments of inertia.

Moment of inertiaEnergy
0.001 kg·m² (small fan impeller)1.974 J
0.01 kg·m² (bench-grinder wheel)19.74 J
0.1 kg·m² (car flywheel)197.4 J
1 kg·m² (industrial flywheel)1.974 kJ

Multiples of this speed

Rizwan Malik headshot

Rizwan Malik

Founder & Editor

  • Formulas checked against the BIPM SI Brochure
  • Unit definitions per NIST SP 811

Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.

Frequently asked questions