34 RPM to Radians Per Second Converter
Instant conversion for 34 RPM to rad/s (3.560472 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 3.5604717
- Degrees per Second (°/s)
- 204 °/s
- Hertz (Hz)
- 0.566667 Hz
- Revolutions per Second (RPS)
- 0.566667 rev/s
- Revolutions per Hour (RPH)
- 2,040 rev/hr
- Revolutions per Day
- 48,960 rev/day
- Radians per Minute (rad/min)
- 213.6283 rad/min
- Milliradians per Second (mrad/s)
- 3,560.4717 mrad/s
- Period (seconds per rev)
- 1.764706 s/rev
- Exact Formula
- 34 × π/30 = 3.5604717 rad/s
- Nearest Real-World Example
- Ceiling fan — high (200 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 34 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 34 × (π / 30) = 3.560472 rad/s
Exact fraction: 34π/30 rad/s · Reciprocal: 3.56 rad/s × (30/π) = 34 RPM
Reverse Conversion: 3.56 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
34 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
34 RPM = 17π/15 rad/s ≈ 3.560472 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 3.5598 rad/s instead of the exact 3.5605 rad/s — an error of 0.0006717 rad/s.
What this speed looks like in practice
At 34 RPM a shaft turns about 1.02× as fast as an LP record (33⅓ RPM). A 7-inch single (45 RPM) turns about 1.32× faster.
Revolutions over time
That is 2,040 revolutions per hour and 48,960 per day. A quarter turn (90°) takes 441 ms, and the shaft sweeps 0.204° every millisecond.
Rim speed and centripetal load at ω = 3.5605 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 0.0356 m/s · 0.1282 km/h | 0.1268 m/s² · 0.01293 g |
| 5 cm | 10 cm | 0.178 m/s · 0.6409 km/h | 0.6338 m/s² · 0.06463 g |
| 10 cm | 20 cm | 0.356 m/s · 1.282 km/h | 1.268 m/s² · 0.1293 g |
| 25 cm | 50 cm | 0.8901 m/s · 3.204 km/h | 3.169 m/s² · 0.3232 g |
| 50 cm | 1 m | 1.78 m/s · 6.409 km/h | 6.338 m/s² · 0.6463 g |
| 1 m | 2 m | 3.56 m/s · 12.82 km/h | 12.68 m/s² · 1.293 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 34 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 0.5667 Hz | Below typical VFD range — use a gearbox |
| 4 | 1.133 Hz | Below typical VFD range — use a gearbox |
| 6 | 1.7 Hz | Below typical VFD range — use a gearbox |
| 8 | 2.267 Hz | Below typical VFD range — use a gearbox |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 11.33 RPM · 1.187 rad/s | ×3 |
| 5:1 | 6.8 RPM · 0.7121 rad/s | ×5 |
| 10:1 | 3.4 RPM · 0.356 rad/s | ×10 |
| 30:1 | 1.133 RPM · 0.1187 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 0.006338 J |
| 0.01 kg·m² (bench-grinder wheel) | 0.06338 J |
| 0.1 kg·m² (car flywheel) | 0.6338 J |
| 1 kg·m² (industrial flywheel) | 6.338 J |
Multiples of this speed
- 0.5× = 17 RPM1.7802 rad/s
- 2× = 68 RPM7.1209 rad/s
- 5× = 170 RPM17.8024 rad/s
- 10× = 340 RPM35.6047 rad/s

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 34 RPM to radians per second, multiply 34 by π and divide by 30: 34 × (π / 30) = 3.560472 rad/s (approx. 3.56 rad/s).
34 RPM equals 0.5667 Hz (revolutions per second), calculated by dividing 34 by 60 seconds.
To convert 3.56 rad/s back to RPM, multiply by 30 and divide by π: 3.56 × (30 / π) ≈ 34 RPM.
At 34 RPM, one full 360° revolution takes 1.7647 seconds (1764.71 ms).
A 4-pole induction motor has a synchronous speed of 34 RPM at 1.1333 Hz (f = RPM × poles / 120 = 34 × 4 / 120). That is far below a drive's usable range, so in practice a standard motor runs faster and a gearbox or gearmotor brings the output down to this speed.
Tangential speed is v = ω·r = 3.560472 rad/s × 0.1 m = 0.356 m/s (1.2818 km/h). The centripetal acceleration at the rim is ω²·r = 1.2677 m/s².