25 RPM to Radians Per Second Converter
Instant conversion for 25 RPM to rad/s (2.617994 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 2.6179939
- Degrees per Second (°/s)
- 150 °/s
- Hertz (Hz)
- 0.416667 Hz
- Revolutions per Second (RPS)
- 0.416667 rev/s
- Revolutions per Hour (RPH)
- 1,500 rev/hr
- Revolutions per Day
- 36,000 rev/day
- Radians per Minute (rad/min)
- 157.07963 rad/min
- Milliradians per Second (mrad/s)
- 2,617.9939 mrad/s
- Period (seconds per rev)
- 2.4 s/rev
- Exact Formula
- 25 × π/30 = 2.6179939 rad/s
- Nearest Real-World Example
- Ceiling fan — high (200 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 25 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 25 × (π / 30) = 2.617994 rad/s
Exact fraction: 25π/30 rad/s · Reciprocal: 2.618 rad/s × (30/π) = 25 RPM
Reverse Conversion: 2.618 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
25 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
25 RPM = 5π/6 rad/s ≈ 2.617994 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 2.6175 rad/s instead of the exact 2.618 rad/s — an error of 0.0004939 rad/s.
What this speed looks like in practice
At 25 RPM a shaft turns about 1.67× as fast as a utility-scale wind turbine rotor. An LP record (33⅓ RPM) turns about 1.33× faster.
Revolutions over time
That is 1,500 revolutions per hour and 36,000 per day. A quarter turn (90°) takes 600 ms, and the shaft sweeps 0.15° every millisecond.
Rim speed and centripetal load at ω = 2.618 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 0.02618 m/s · 0.09425 km/h | 0.06854 m/s² · 0.006989 g |
| 5 cm | 10 cm | 0.1309 m/s · 0.4712 km/h | 0.3427 m/s² · 0.03495 g |
| 10 cm | 20 cm | 0.2618 m/s · 0.9425 km/h | 0.6854 m/s² · 0.06989 g |
| 25 cm | 50 cm | 0.6545 m/s · 2.356 km/h | 1.713 m/s² · 0.1747 g |
| 50 cm | 1 m | 1.309 m/s · 4.712 km/h | 3.427 m/s² · 0.3495 g |
| 1 m | 2 m | 2.618 m/s · 9.425 km/h | 6.854 m/s² · 0.6989 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 25 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 0.4167 Hz | Below typical VFD range — use a gearbox |
| 4 | 0.8333 Hz | Below typical VFD range — use a gearbox |
| 6 | 1.25 Hz | Below typical VFD range — use a gearbox |
| 8 | 1.667 Hz | Below typical VFD range — use a gearbox |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 8.333 RPM · 0.8727 rad/s | ×3 |
| 5:1 | 5 RPM · 0.5236 rad/s | ×5 |
| 10:1 | 2.5 RPM · 0.2618 rad/s | ×10 |
| 30:1 | 0.8333 RPM · 0.08727 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 0.003427 J |
| 0.01 kg·m² (bench-grinder wheel) | 0.03427 J |
| 0.1 kg·m² (car flywheel) | 0.3427 J |
| 1 kg·m² (industrial flywheel) | 3.427 J |
Multiples of this speed
- 0.5× = 12.5 RPM1.309 rad/s
- 2× = 50 RPM5.236 rad/s
- 5× = 125 RPM13.09 rad/s
- 10× = 250 RPM26.1799 rad/s

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 25 RPM to radians per second, multiply 25 by π and divide by 30: 25 × (π / 30) = 2.617994 rad/s (approx. 2.618 rad/s).
25 RPM equals 0.4167 Hz (revolutions per second), calculated by dividing 25 by 60 seconds.
To convert 2.618 rad/s back to RPM, multiply by 30 and divide by π: 2.618 × (30 / π) ≈ 25 RPM.
At 25 RPM, one full 360° revolution takes 2.4 seconds (2400.00 ms).
A 4-pole induction motor has a synchronous speed of 25 RPM at 0.8333 Hz (f = RPM × poles / 120 = 25 × 4 / 120). That is far below a drive's usable range, so in practice a standard motor runs faster and a gearbox or gearmotor brings the output down to this speed.
Tangential speed is v = ω·r = 2.617994 rad/s × 0.1 m = 0.2618 m/s (0.9425 km/h). The centripetal acceleration at the rim is ω²·r = 0.6854 m/s².