24 RPM to Radians Per Second Converter
Instant conversion for 24 RPM to rad/s (2.513274 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 2.5132741
- Degrees per Second (°/s)
- 144 °/s
- Hertz (Hz)
- 0.4 Hz
- Revolutions per Second (RPS)
- 0.4 rev/s
- Revolutions per Hour (RPH)
- 1,440 rev/hr
- Revolutions per Day
- 34,560 rev/day
- Radians per Minute (rad/min)
- 150.79645 rad/min
- Milliradians per Second (mrad/s)
- 2,513.2741 mrad/s
- Period (seconds per rev)
- 2.5 s/rev
- Exact Formula
- 24 × π/30 = 2.5132741 rad/s
- Nearest Real-World Example
- Ceiling fan — high (200 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 24 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 24 × (π / 30) = 2.513274 rad/s
Exact fraction: 24π/30 rad/s · Reciprocal: 2.513 rad/s × (30/π) = 24 RPM
Reverse Conversion: 2.513 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
24 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
24 RPM = 4π/5 rad/s ≈ 2.513274 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 2.5128 rad/s instead of the exact 2.5133 rad/s — an error of 0.0004741 rad/s.
What this speed looks like in practice
At 24 RPM a shaft turns about 1.6× as fast as a utility-scale wind turbine rotor. An LP record (33⅓ RPM) turns about 1.39× faster.
Revolutions over time
That is 1,440 revolutions per hour and 34,560 per day. A quarter turn (90°) takes 625 ms, and the shaft sweeps 0.144° every millisecond.
Rim speed and centripetal load at ω = 2.5133 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 0.02513 m/s · 0.09048 km/h | 0.06317 m/s² · 0.006441 g |
| 5 cm | 10 cm | 0.1257 m/s · 0.4524 km/h | 0.3158 m/s² · 0.03221 g |
| 10 cm | 20 cm | 0.2513 m/s · 0.9048 km/h | 0.6317 m/s² · 0.06441 g |
| 25 cm | 50 cm | 0.6283 m/s · 2.262 km/h | 1.579 m/s² · 0.161 g |
| 50 cm | 1 m | 1.257 m/s · 4.524 km/h | 3.158 m/s² · 0.3221 g |
| 1 m | 2 m | 2.513 m/s · 9.048 km/h | 6.317 m/s² · 0.6441 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 24 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 0.4 Hz | Below typical VFD range — use a gearbox |
| 4 | 0.8 Hz | Below typical VFD range — use a gearbox |
| 6 | 1.2 Hz | Below typical VFD range — use a gearbox |
| 8 | 1.6 Hz | Below typical VFD range — use a gearbox |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 8 RPM · 0.8378 rad/s | ×3 |
| 5:1 | 4.8 RPM · 0.5027 rad/s | ×5 |
| 10:1 | 2.4 RPM · 0.2513 rad/s | ×10 |
| 30:1 | 0.8 RPM · 0.08378 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 0.003158 J |
| 0.01 kg·m² (bench-grinder wheel) | 0.03158 J |
| 0.1 kg·m² (car flywheel) | 0.3158 J |
| 1 kg·m² (industrial flywheel) | 3.158 J |
Multiples of this speed
- 0.5× = 12 RPM1.2566 rad/s
- 2× = 48 RPM5.0265 rad/s
- 5× = 120 RPM12.5664 rad/s
- 10× = 240 RPM25.1327 rad/s

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 24 RPM to radians per second, multiply 24 by π and divide by 30: 24 × (π / 30) = 2.513274 rad/s (approx. 2.513 rad/s).
24 RPM equals 0.4000 Hz (revolutions per second), calculated by dividing 24 by 60 seconds.
To convert 2.513 rad/s back to RPM, multiply by 30 and divide by π: 2.513 × (30 / π) ≈ 24 RPM.
At 24 RPM, one full 360° revolution takes 2.5 seconds (2500.00 ms).
A 4-pole induction motor has a synchronous speed of 24 RPM at 0.8 Hz (f = RPM × poles / 120 = 24 × 4 / 120). That is far below a drive's usable range, so in practice a standard motor runs faster and a gearbox or gearmotor brings the output down to this speed.
Tangential speed is v = ω·r = 2.513274 rad/s × 0.1 m = 0.2513 m/s (0.9048 km/h). The centripetal acceleration at the rim is ω²·r = 0.6317 m/s².