250 RPM to Radians Per Second Converter
Instant conversion for 250 RPM to rad/s (26.179939 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 26.179939
- Degrees per Second (°/s)
- 1,500 °/s
- Hertz (Hz)
- 4.166667 Hz
- Revolutions per Second (RPS)
- 4.166667 rev/s
- Revolutions per Hour (RPH)
- 15,000 rev/hr
- Revolutions per Day
- 360,000 rev/day
- Radians per Minute (rad/min)
- 1,570.7963 rad/min
- Milliradians per Second (mrad/s)
- 26,179.939 mrad/s
- Period (seconds per rev)
- 0.24 s/rev
- Exact Formula
- 250 × π/30 = 26.179939 rad/s
- Nearest Real-World Example
- Ceiling fan — high (200 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 250 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 250 × (π / 30) = 26.179939 rad/s
Exact fraction: 250π/30 rad/s · Reciprocal: 26.18 rad/s × (30/π) = 250 RPM
Reverse Conversion: 26.18 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
250 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
250 RPM = 25π/3 rad/s ≈ 26.179939 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 26.175 rad/s instead of the exact 26.1799 rad/s — an error of 0.004939 rad/s.
What this speed looks like in practice
At 250 RPM a shaft turns about 1.25× as fast as a ceiling fan on high. A car engine at idle turns about 3× faster.
Revolutions over time
That is 15,000 revolutions per hour and 360,000 per day. A quarter turn (90°) takes 60 ms, and the shaft sweeps 1.5° every millisecond.
Rim speed and centripetal load at ω = 26.1799 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 0.2618 m/s · 0.9425 km/h | 6.854 m/s² · 0.6989 g |
| 5 cm | 10 cm | 1.309 m/s · 4.712 km/h | 34.27 m/s² · 3.495 g |
| 10 cm | 20 cm | 2.618 m/s · 9.425 km/h | 68.54 m/s² · 6.989 g |
| 25 cm | 50 cm | 6.545 m/s · 23.56 km/h | 171.3 m/s² · 17.47 g |
| 50 cm | 1 m | 13.09 m/s · 47.12 km/h | 342.7 m/s² · 34.95 g |
| 1 m | 2 m | 26.18 m/s · 94.25 km/h | 685.4 m/s² · 69.89 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 250 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 4.167 Hz | Below typical VFD range — use a gearbox |
| 4 | 8.333 Hz | Reachable with a VFD |
| 6 | 12.5 Hz | Reachable with a VFD |
| 8 | 16.67 Hz | Reachable with a VFD |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 83.33 RPM · 8.727 rad/s | ×3 |
| 5:1 | 50 RPM · 5.236 rad/s | ×5 |
| 10:1 | 25 RPM · 2.618 rad/s | ×10 |
| 30:1 | 8.333 RPM · 0.8727 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 0.3427 J |
| 0.01 kg·m² (bench-grinder wheel) | 3.427 J |
| 0.1 kg·m² (car flywheel) | 34.27 J |
| 1 kg·m² (industrial flywheel) | 342.7 J |
Multiples of this speed
- 0.5× = 125 RPM13.09 rad/s
- 2× = 500 RPM52.3599 rad/s
- 5× = 1,250 RPM130.8997 rad/s
- 10× = 2,500 RPM261.7994 rad/s

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 250 RPM to radians per second, multiply 250 by π and divide by 30: 250 × (π / 30) = 26.179939 rad/s (approx. 26.18 rad/s).
250 RPM equals 4.1667 Hz (revolutions per second), calculated by dividing 250 by 60 seconds.
To convert 26.18 rad/s back to RPM, multiply by 30 and divide by π: 26.18 × (30 / π) ≈ 250 RPM.
At 250 RPM, one full 360° revolution takes 0.24 seconds (240.00 ms).
A 4-pole induction motor has a synchronous speed of 250 RPM at 8.3333 Hz (f = RPM × poles / 120 = 250 × 4 / 120). Under load it runs roughly 2–4% below synchronous speed, so a VFD is normally set slightly higher.
Tangential speed is v = ω·r = 26.179939 rad/s × 0.1 m = 2.618 m/s (9.4248 km/h). The centripetal acceleration at the rim is ω²·r = 68.5389 m/s².