180 RPM to Radians Per Second Converter
Instant conversion for 180 RPM to rad/s (18.849556 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 18.849556
- Degrees per Second (°/s)
- 1,080 °/s
- Hertz (Hz)
- 3 Hz
- Revolutions per Second (RPS)
- 3 rev/s
- Revolutions per Hour (RPH)
- 10,800 rev/hr
- Revolutions per Day
- 259,200 rev/day
- Radians per Minute (rad/min)
- 1,130.9734 rad/min
- Milliradians per Second (mrad/s)
- 18,849.556 mrad/s
- Period (seconds per rev)
- 0.333333 s/rev
- Exact Formula
- 180 × π/30 = 18.849556 rad/s
- Nearest Real-World Example
- Ceiling fan — high (200 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 180 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 180 × (π / 30) = 18.849556 rad/s
Exact fraction: 180π/30 rad/s · Reciprocal: 18.85 rad/s × (30/π) = 180 RPM
Reverse Conversion: 18.85 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
180 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
180 RPM = 6π rad/s ≈ 18.849556 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 18.846 rad/s instead of the exact 18.8496 rad/s — an error of 0.003556 rad/s.
What this speed looks like in practice
At 180 RPM a shaft turns about 4× as fast as a 7-inch single (45 RPM). A ceiling fan on high turns about 1.11× faster.
Revolutions over time
That is 10,800 revolutions per hour and 259,200 per day. A quarter turn (90°) takes 83.3 ms, and the shaft sweeps 1.08° every millisecond.
Rim speed and centripetal load at ω = 18.8496 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 0.1885 m/s · 0.6786 km/h | 3.553 m/s² · 0.3623 g |
| 5 cm | 10 cm | 0.9425 m/s · 3.393 km/h | 17.77 m/s² · 1.812 g |
| 10 cm | 20 cm | 1.885 m/s · 6.786 km/h | 35.53 m/s² · 3.623 g |
| 25 cm | 50 cm | 4.712 m/s · 16.96 km/h | 88.83 m/s² · 9.058 g |
| 50 cm | 1 m | 9.425 m/s · 33.93 km/h | 177.7 m/s² · 18.12 g |
| 1 m | 2 m | 18.85 m/s · 67.86 km/h | 355.3 m/s² · 36.23 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 180 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 3 Hz | Below typical VFD range — use a gearbox |
| 4 | 6 Hz | Reachable with a VFD |
| 6 | 9 Hz | Reachable with a VFD |
| 8 | 12 Hz | Reachable with a VFD |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 60 RPM · 6.283 rad/s | ×3 |
| 5:1 | 36 RPM · 3.77 rad/s | ×5 |
| 10:1 | 18 RPM · 1.885 rad/s | ×10 |
| 30:1 | 6 RPM · 0.6283 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 0.1777 J |
| 0.01 kg·m² (bench-grinder wheel) | 1.777 J |
| 0.1 kg·m² (car flywheel) | 17.77 J |
| 1 kg·m² (industrial flywheel) | 177.7 J |
Multiples of this speed

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 180 RPM to radians per second, multiply 180 by π and divide by 30: 180 × (π / 30) = 18.849556 rad/s (approx. 18.85 rad/s).
180 RPM equals 3.0000 Hz (revolutions per second), calculated by dividing 180 by 60 seconds.
To convert 18.85 rad/s back to RPM, multiply by 30 and divide by π: 18.85 × (30 / π) ≈ 180 RPM.
At 180 RPM, one full 360° revolution takes 0.3333 seconds (333.33 ms).
A 4-pole induction motor has a synchronous speed of 180 RPM at 6 Hz (f = RPM × poles / 120 = 180 × 4 / 120). Under load it runs roughly 2–4% below synchronous speed, so a VFD is normally set slightly higher.
Tangential speed is v = ω·r = 18.849556 rad/s × 0.1 m = 1.885 m/s (6.7858 km/h). The centripetal acceleration at the rim is ω²·r = 35.5306 m/s².