RPM to Radians Per SecondRPM to rad/s

72 RPM to Radians Per Second Converter

Instant conversion for 72 RPM to rad/s (7.539822 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.

m
Result7.539822 rad/s
Radians per Second (rad/s)
7.5398224
Degrees per Second (°/s)
432 °/s
Hertz (Hz)
1.2 Hz
Revolutions per Second (RPS)
1.2 rev/s
Revolutions per Hour (RPH)
4,320 rev/hr
Revolutions per Day
103,680 rev/day
Radians per Minute (rad/min)
452.38934 rad/min
Milliradians per Second (mrad/s)
7,539.8224 mrad/s
Period (seconds per rev)
0.833333 s/rev
Exact Formula
72 × π/30 = 7.5398224 rad/s
Nearest Real-World Example
Ceiling fan — high (200 RPM)
Precision Drift Meter (Exact π/30 vs. 0.10472 Rounded)Zero Drift Here

Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:

Exact Value (π/30):7.539822 rad/s
Rounded (0.10472):7.539840 rad/s
Angular Error / Hour:3.64° / hr

Worked Conversion: 72 RPM to Radians Per Second

To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.

rad/s = 72 × (π / 30) = 7.539822 rad/s

Exact fraction: 72π/30 rad/s · Reciprocal: 7.54 rad/s × (30/π) = 72 RPM

Angular Velocity
7.539822 rad/s
Frequency
1.2 Hz
Degrees / Second
432 °/s
Period per Rev
0.8333 s
Engineering Context: Under 100 RPM you are around one revolution per second, the range of bicycle wheels at low speed, slow ceiling fans and hand-cranked machinery.

Reverse Conversion: 7.54 rad/s to RPM

Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.

Browse Reverse Conversions →

In-Depth Engineering Guides & References

5.36 Rad/s to RPM: College Physics Homework Benchmark Solution— Serway & Halliday kinematics proof and analytical derivation.
RPM to Radians Per Second Formula & Calculus Proof— Dimensional cancellation, π/30 derivation, and IEEE 754 precision.
Angular Velocity Guide & Rotational Kinematics— SI standards, tangential velocity (v = ω·r), and centripetal acceleration.
Complete Conversion Index— Browse pre-calculated conversion speeds from 1 to 20,000 RPM.

72 RPM: exact form, real-world scale & engineering tables

Exact answer in terms of π

72 RPM = 12π/5 rad/s ≈ 7.539822 rad/s

Reduced fraction — keep this form through multi-step problems and only round at the end.

Rounding check

Using the rounded factor 0.1047 gives 7.5384 rad/s instead of the exact 7.5398 rad/s — an error of 0.001422 rad/s.

What this speed looks like in practice

At 72 RPM a shaft turns about 1.6× as fast as a 7-inch single (45 RPM). A ceiling fan on high turns about 2.78× faster.

Revolutions over time

That is 4,320 revolutions per hour and 103,680 per day. A quarter turn (90°) takes 208 ms, and the shaft sweeps 0.432° every millisecond.

Rim speed and centripetal load at ω = 7.5398 rad/s

Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.

RadiusDiameterRim speedCentripetal acceleration
1 cm2 cm0.0754 m/s · 0.2714 km/h0.5685 m/s² · 0.05797 g
5 cm10 cm0.377 m/s · 1.357 km/h2.842 m/s² · 0.2898 g
10 cm20 cm0.754 m/s · 2.714 km/h5.685 m/s² · 0.5797 g
25 cm50 cm1.885 m/s · 6.786 km/h14.21 m/s² · 1.449 g
50 cm1 m3.77 m/s · 13.57 km/h28.42 m/s² · 2.898 g
1 m2 m7.54 m/s · 27.14 km/h56.85 m/s² · 5.797 g

Driving this speed with an AC motor

Supply frequency an induction motor would need for a synchronous speed of 72 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.

PolesSupply frequencyPractical note
21.2 HzBelow typical VFD range — use a gearbox
42.4 HzBelow typical VFD range — use a gearbox
63.6 HzBelow typical VFD range — use a gearbox
84.8 HzBelow typical VFD range — use a gearbox

Through a reduction gearbox

Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.

RatioOutput speedTorque ×
3:124 RPM · 2.513 rad/s×3
5:114.4 RPM · 1.508 rad/s×5
10:17.2 RPM · 0.754 rad/s×10
30:12.4 RPM · 0.2513 rad/s×30

Stored rotational energy

Kinetic energy E = ½·I·ω² for a range of moments of inertia.

Moment of inertiaEnergy
0.001 kg·m² (small fan impeller)0.02842 J
0.01 kg·m² (bench-grinder wheel)0.2842 J
0.1 kg·m² (car flywheel)2.842 J
1 kg·m² (industrial flywheel)28.42 J

Multiples of this speed

Rizwan Malik headshot

Rizwan Malik

Founder & Editor

  • Formulas checked against the BIPM SI Brochure
  • Unit definitions per NIST SP 811

Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.

Frequently asked questions