RPM to Radians Per SecondRPM to rad/s

48 RPM to Radians Per Second Converter

Instant conversion for 48 RPM to rad/s (5.026548 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.

m
Result5.026548 rad/s
Radians per Second (rad/s)
5.0265482
Degrees per Second (°/s)
288 °/s
Hertz (Hz)
0.8 Hz
Revolutions per Second (RPS)
0.8 rev/s
Revolutions per Hour (RPH)
2,880 rev/hr
Revolutions per Day
69,120 rev/day
Radians per Minute (rad/min)
301.59289 rad/min
Milliradians per Second (mrad/s)
5,026.5482 mrad/s
Period (seconds per rev)
1.25 s/rev
Exact Formula
48 × π/30 = 5.0265482 rad/s
Nearest Real-World Example
Ceiling fan — high (200 RPM)
Precision Drift Meter (Exact π/30 vs. 0.10472 Rounded)Zero Drift Here

Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:

Exact Value (π/30):5.026548 rad/s
Rounded (0.10472):5.026560 rad/s
Angular Error / Hour:2.42° / hr

Worked Conversion: 48 RPM to Radians Per Second

To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.

rad/s = 48 × (π / 30) = 5.026548 rad/s

Exact fraction: 48π/30 rad/s · Reciprocal: 5.027 rad/s × (30/π) = 48 RPM

Angular Velocity
5.026548 rad/s
Frequency
0.8 Hz
Degrees / Second
288 °/s
Period per Rev
1.25 s
Engineering Context: The 20–50 RPM band is turntable and potter's-wheel country, and it brackets both vinyl standards (33⅓ and 45 RPM).

Reverse Conversion: 5.027 rad/s to RPM

Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.

Browse Reverse Conversions →

In-Depth Engineering Guides & References

5.36 Rad/s to RPM: College Physics Homework Benchmark Solution— Serway & Halliday kinematics proof and analytical derivation.
RPM to Radians Per Second Formula & Calculus Proof— Dimensional cancellation, π/30 derivation, and IEEE 754 precision.
Angular Velocity Guide & Rotational Kinematics— SI standards, tangential velocity (v = ω·r), and centripetal acceleration.
Complete Conversion Index— Browse pre-calculated conversion speeds from 1 to 20,000 RPM.

48 RPM: exact form, real-world scale & engineering tables

Exact answer in terms of π

48 RPM = 8π/5 rad/s ≈ 5.026548 rad/s

Reduced fraction — keep this form through multi-step problems and only round at the end.

Rounding check

Using the rounded factor 0.1047 gives 5.0256 rad/s instead of the exact 5.0265 rad/s — an error of 0.0009482 rad/s.

What this speed looks like in practice

At 48 RPM a shaft turns about 1.07× as fast as a 7-inch single (45 RPM). A ceiling fan on high turns about 4.17× faster.

Revolutions over time

That is 2,880 revolutions per hour and 69,120 per day. A quarter turn (90°) takes 313 ms, and the shaft sweeps 0.288° every millisecond.

Rim speed and centripetal load at ω = 5.0265 rad/s

Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.

RadiusDiameterRim speedCentripetal acceleration
1 cm2 cm0.05027 m/s · 0.181 km/h0.2527 m/s² · 0.02576 g
5 cm10 cm0.2513 m/s · 0.9048 km/h1.263 m/s² · 0.1288 g
10 cm20 cm0.5027 m/s · 1.81 km/h2.527 m/s² · 0.2576 g
25 cm50 cm1.257 m/s · 4.524 km/h6.317 m/s² · 0.6441 g
50 cm1 m2.513 m/s · 9.048 km/h12.63 m/s² · 1.288 g
1 m2 m5.027 m/s · 18.1 km/h25.27 m/s² · 2.576 g

Driving this speed with an AC motor

Supply frequency an induction motor would need for a synchronous speed of 48 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.

PolesSupply frequencyPractical note
20.8 HzBelow typical VFD range — use a gearbox
41.6 HzBelow typical VFD range — use a gearbox
62.4 HzBelow typical VFD range — use a gearbox
83.2 HzBelow typical VFD range — use a gearbox

Through a reduction gearbox

Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.

RatioOutput speedTorque ×
3:116 RPM · 1.676 rad/s×3
5:19.6 RPM · 1.005 rad/s×5
10:14.8 RPM · 0.5027 rad/s×10
30:11.6 RPM · 0.1676 rad/s×30

Stored rotational energy

Kinetic energy E = ½·I·ω² for a range of moments of inertia.

Moment of inertiaEnergy
0.001 kg·m² (small fan impeller)0.01263 J
0.01 kg·m² (bench-grinder wheel)0.1263 J
0.1 kg·m² (car flywheel)1.263 J
1 kg·m² (industrial flywheel)12.63 J

Multiples of this speed

Rizwan Malik headshot

Rizwan Malik

Founder & Editor

  • Formulas checked against the BIPM SI Brochure
  • Unit definitions per NIST SP 811

Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.

Frequently asked questions