9 RPM to Radians Per Second Converter
Instant conversion for 9 RPM to rad/s (0.942478 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 0.9424778
- Degrees per Second (°/s)
- 54 °/s
- Hertz (Hz)
- 0.15 Hz
- Revolutions per Second (RPS)
- 0.15 rev/s
- Revolutions per Hour (RPH)
- 540 rev/hr
- Revolutions per Day
- 12,960 rev/day
- Radians per Minute (rad/min)
- 56.548668 rad/min
- Milliradians per Second (mrad/s)
- 942.4778 mrad/s
- Period (seconds per rev)
- 6.666667 s/rev
- Exact Formula
- 9 × π/30 = 0.9424778 rad/s
- Nearest Real-World Example
- Ceiling fan — high (200 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 9 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 9 × (π / 30) = 0.942478 rad/s
Exact fraction: 9π/30 rad/s · Reciprocal: 0.9425 rad/s × (30/π) = 9 RPM
Reverse Conversion: 0.9425 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
9 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
9 RPM = 3π/10 rad/s ≈ 0.942478 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 0.9423 rad/s instead of the exact 0.9425 rad/s — an error of 0.0001778 rad/s.
What this speed looks like in practice
At 9 RPM a shaft turns about 9× as fast as a clock's second hand. A utility-scale wind turbine rotor turns about 1.67× faster.
Revolutions over time
That is 540 revolutions per hour and 12,960 per day. A quarter turn (90°) takes 1.67 s, and the shaft sweeps 0.054° every millisecond.
Rim speed and centripetal load at ω = 0.9425 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 0.009425 m/s · 0.03393 km/h | 0.008883 m/s² · 0.0009058 g |
| 5 cm | 10 cm | 0.04712 m/s · 0.1696 km/h | 0.04441 m/s² · 0.004529 g |
| 10 cm | 20 cm | 0.09425 m/s · 0.3393 km/h | 0.08883 m/s² · 0.009058 g |
| 25 cm | 50 cm | 0.2356 m/s · 0.8482 km/h | 0.2221 m/s² · 0.02264 g |
| 50 cm | 1 m | 0.4712 m/s · 1.696 km/h | 0.4441 m/s² · 0.04529 g |
| 1 m | 2 m | 0.9425 m/s · 3.393 km/h | 0.8883 m/s² · 0.09058 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 9 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 0.15 Hz | Below typical VFD range — use a gearbox |
| 4 | 0.3 Hz | Below typical VFD range — use a gearbox |
| 6 | 0.45 Hz | Below typical VFD range — use a gearbox |
| 8 | 0.6 Hz | Below typical VFD range — use a gearbox |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 3 RPM · 0.3142 rad/s | ×3 |
| 5:1 | 1.8 RPM · 0.1885 rad/s | ×5 |
| 10:1 | 0.9 RPM · 0.09425 rad/s | ×10 |
| 30:1 | 0.3 RPM · 0.03142 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 0.0004441 J |
| 0.01 kg·m² (bench-grinder wheel) | 0.004441 J |
| 0.1 kg·m² (car flywheel) | 0.04441 J |
| 1 kg·m² (industrial flywheel) | 0.4441 J |
Multiples of this speed
- 0.5× = 4.5 RPM0.4712 rad/s
- 2× = 18 RPM1.885 rad/s
- 5× = 45 RPM4.7124 rad/s
- 10× = 90 RPM9.4248 rad/s

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 9 RPM to radians per second, multiply 9 by π and divide by 30: 9 × (π / 30) = 0.942478 rad/s (approx. 0.9425 rad/s).
9 RPM equals 0.1500 Hz (revolutions per second), calculated by dividing 9 by 60 seconds.
To convert 0.9425 rad/s back to RPM, multiply by 30 and divide by π: 0.9425 × (30 / π) ≈ 9 RPM.
At 9 RPM, one full 360° revolution takes 6.6667 seconds (6666.67 ms).
A 4-pole induction motor has a synchronous speed of 9 RPM at 0.3 Hz (f = RPM × poles / 120 = 9 × 4 / 120). That is far below a drive's usable range, so in practice a standard motor runs faster and a gearbox or gearmotor brings the output down to this speed.
Tangential speed is v = ω·r = 0.942478 rad/s × 0.1 m = 0.0942 m/s (0.3393 km/h). The centripetal acceleration at the rim is ω²·r = 0.0888 m/s².