8 RPM to Radians Per Second Converter
Instant conversion for 8 RPM to rad/s (0.837758 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 0.83775804
- Degrees per Second (°/s)
- 48 °/s
- Hertz (Hz)
- 0.133333 Hz
- Revolutions per Second (RPS)
- 0.133333 rev/s
- Revolutions per Hour (RPH)
- 480 rev/hr
- Revolutions per Day
- 11,520 rev/day
- Radians per Minute (rad/min)
- 50.265482 rad/min
- Milliradians per Second (mrad/s)
- 837.75804 mrad/s
- Period (seconds per rev)
- 7.5 s/rev
- Exact Formula
- 8 × π/30 = 0.83775804 rad/s
- Nearest Real-World Example
- Ceiling fan — high (200 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 8 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 8 × (π / 30) = 0.837758 rad/s
Exact fraction: 8π/30 rad/s · Reciprocal: 0.8378 rad/s × (30/π) = 8 RPM
Reverse Conversion: 0.8378 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
8 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
8 RPM = 4π/15 rad/s ≈ 0.837758 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 0.8376 rad/s instead of the exact 0.8378 rad/s — an error of 0.000158 rad/s.
What this speed looks like in practice
At 8 RPM a shaft turns about 8× as fast as a clock's second hand. A utility-scale wind turbine rotor turns about 1.88× faster.
Revolutions over time
That is 480 revolutions per hour and 11,520 per day. A quarter turn (90°) takes 1.88 s, and the shaft sweeps 0.048° every millisecond.
Rim speed and centripetal load at ω = 0.8378 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 0.008378 m/s · 0.03016 km/h | 0.007018 m/s² · 0.0007157 g |
| 5 cm | 10 cm | 0.04189 m/s · 0.1508 km/h | 0.03509 m/s² · 0.003578 g |
| 10 cm | 20 cm | 0.08378 m/s · 0.3016 km/h | 0.07018 m/s² · 0.007157 g |
| 25 cm | 50 cm | 0.2094 m/s · 0.754 km/h | 0.1755 m/s² · 0.01789 g |
| 50 cm | 1 m | 0.4189 m/s · 1.508 km/h | 0.3509 m/s² · 0.03578 g |
| 1 m | 2 m | 0.8378 m/s · 3.016 km/h | 0.7018 m/s² · 0.07157 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 8 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 0.1333 Hz | Below typical VFD range — use a gearbox |
| 4 | 0.2667 Hz | Below typical VFD range — use a gearbox |
| 6 | 0.4 Hz | Below typical VFD range — use a gearbox |
| 8 | 0.5333 Hz | Below typical VFD range — use a gearbox |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 2.667 RPM · 0.2793 rad/s | ×3 |
| 5:1 | 1.6 RPM · 0.1676 rad/s | ×5 |
| 10:1 | 0.8 RPM · 0.08378 rad/s | ×10 |
| 30:1 | 0.2667 RPM · 0.02793 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 0.0003509 J |
| 0.01 kg·m² (bench-grinder wheel) | 0.003509 J |
| 0.1 kg·m² (car flywheel) | 0.03509 J |
| 1 kg·m² (industrial flywheel) | 0.3509 J |
Multiples of this speed

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 8 RPM to radians per second, multiply 8 by π and divide by 30: 8 × (π / 30) = 0.837758 rad/s (approx. 0.8378 rad/s).
8 RPM equals 0.1333 Hz (revolutions per second), calculated by dividing 8 by 60 seconds.
To convert 0.8378 rad/s back to RPM, multiply by 30 and divide by π: 0.8378 × (30 / π) ≈ 8 RPM.
At 8 RPM, one full 360° revolution takes 7.5 seconds (7500.00 ms).
A 4-pole induction motor has a synchronous speed of 8 RPM at 0.2667 Hz (f = RPM × poles / 120 = 8 × 4 / 120). That is far below a drive's usable range, so in practice a standard motor runs faster and a gearbox or gearmotor brings the output down to this speed.
Tangential speed is v = ω·r = 0.837758 rad/s × 0.1 m = 0.0838 m/s (0.3016 km/h). The centripetal acceleration at the rim is ω²·r = 0.0702 m/s².