3,450 RPM to Radians Per Second Converter
Instant conversion for 3,450 RPM to rad/s (361.283155 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 361.28316
- Degrees per Second (°/s)
- 20,700 °/s
- Hertz (Hz)
- 57.5 Hz
- Revolutions per Second (RPS)
- 57.5 rev/s
- Revolutions per Hour (RPH)
- 207,000 rev/hr
- Revolutions per Day
- 4,968,000 rev/day
- Radians per Minute (rad/min)
- 21,676.989 rad/min
- Milliradians per Second (mrad/s)
- 361,283.16 mrad/s
- Period (seconds per rev)
- 0.017391 s/rev
- Exact Formula
- 3450 × π/30 = 361.28316 rad/s
- Nearest Real-World Example
- Car engine — highway (2,500 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 3,450 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 3450 × (π / 30) = 361.283155 rad/s
Exact fraction: 3450π/30 rad/s · Reciprocal: 361.28 rad/s × (30/π) = 3,450 RPM
Reverse Conversion: 361.28 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
3,450 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
3,450 RPM = 115π rad/s ≈ 361.283155 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 361.215 rad/s instead of the exact 361.2832 rad/s — an error of 0.06816 rad/s.
What this speed looks like in practice
At 3,450 RPM a shaft turns about 1.92× as fast as a 4-pole motor on a 60 Hz grid. A laptop hard drive (5,400 RPM) turns about 1.57× faster.
Revolutions over time
That is 207,000 revolutions per hour and 4,968,000 per day. A quarter turn (90°) takes 4.35 ms, and the shaft sweeps 20.7° every millisecond.
Rim speed and centripetal load at ω = 361.2832 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 3.613 m/s · 13.01 km/h | 1,305 m/s² · 133.1 g |
| 5 cm | 10 cm | 18.06 m/s · 65.03 km/h | 6,526 m/s² · 665.5 g |
| 10 cm | 20 cm | 36.13 m/s · 130.1 km/h | 13,050 m/s² · 1,331 g |
| 25 cm | 50 cm | 90.32 m/s · 325.2 km/h | 32,630 m/s² · 3,327 g |
| 50 cm | 1 m | 180.6 m/s · 650.3 km/h | 65,260 m/s² · 6,655 g |
| 1 m | 2 m | 361.3 m/s · 1,301 km/h | 130,500 m/s² · 13,310 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 3,450 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 57.5 Hz | Reachable with a VFD |
| 4 | 115 Hz | Reachable with a VFD |
| 6 | 172.5 Hz | Above typical VFD range |
| 8 | 230 Hz | Above typical VFD range |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 1,150 RPM · 120.4 rad/s | ×3 |
| 5:1 | 690 RPM · 72.26 rad/s | ×5 |
| 10:1 | 345 RPM · 36.13 rad/s | ×10 |
| 30:1 | 115 RPM · 12.04 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 65.26 J |
| 0.01 kg·m² (bench-grinder wheel) | 652.6 J |
| 0.1 kg·m² (car flywheel) | 6.526 kJ |
| 1 kg·m² (industrial flywheel) | 65.26 kJ |
Multiples of this speed
- 0.5× = 1,725 RPM180.6416 rad/s
- 2× = 6,900 RPM722.5663 rad/s
- 5× = 17,250 RPM1,806.4158 rad/s
- 10× = 34,500 RPM3,612.8316 rad/s

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 3,450 RPM to radians per second, multiply 3450 by π and divide by 30: 3450 × (π / 30) = 361.283155 rad/s (approx. 361.28 rad/s).
3,450 RPM equals 57.5000 Hz (revolutions per second), calculated by dividing 3450 by 60 seconds.
To convert 361.28 rad/s back to RPM, multiply by 30 and divide by π: 361.28 × (30 / π) ≈ 3,450 RPM.
At 3,450 RPM, one full 360° revolution takes 0.0174 seconds (17.39 ms).
A 4-pole induction motor has a synchronous speed of 3,450 RPM at 115 Hz (f = RPM × poles / 120 = 3450 × 4 / 120). Under load it runs roughly 2–4% below synchronous speed, so a VFD is normally set slightly higher.
Tangential speed is v = ω·r = 361.283155 rad/s × 0.1 m = 36.1283 m/s (130.0619 km/h). The centripetal acceleration at the rim is ω²·r = 13052.5518 m/s².