3,400 RPM to Radians Per Second Converter
Instant conversion for 3,400 RPM to rad/s (356.047167 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 356.04717
- Degrees per Second (°/s)
- 20,400 °/s
- Hertz (Hz)
- 56.666667 Hz
- Revolutions per Second (RPS)
- 56.666667 rev/s
- Revolutions per Hour (RPH)
- 204,000 rev/hr
- Revolutions per Day
- 4,896,000 rev/day
- Radians per Minute (rad/min)
- 21,362.83 rad/min
- Milliradians per Second (mrad/s)
- 356,047.17 mrad/s
- Period (seconds per rev)
- 0.017647 s/rev
- Exact Formula
- 3400 × π/30 = 356.04717 rad/s
- Nearest Real-World Example
- Car engine — highway (2,500 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 3,400 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 3400 × (π / 30) = 356.047167 rad/s
Exact fraction: 3400π/30 rad/s · Reciprocal: 356.05 rad/s × (30/π) = 3,400 RPM
Reverse Conversion: 356.05 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
3,400 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
3,400 RPM = 340π/3 rad/s ≈ 356.047167 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 355.98 rad/s instead of the exact 356.0472 rad/s — an error of 0.06717 rad/s.
What this speed looks like in practice
At 3,400 RPM a shaft turns about 1.89× as fast as a 4-pole motor on a 60 Hz grid. A laptop hard drive (5,400 RPM) turns about 1.59× faster.
Revolutions over time
That is 204,000 revolutions per hour and 4,896,000 per day. A quarter turn (90°) takes 4.41 ms, and the shaft sweeps 20.4° every millisecond.
Rim speed and centripetal load at ω = 356.0472 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 3.56 m/s · 12.82 km/h | 1,268 m/s² · 129.3 g |
| 5 cm | 10 cm | 17.8 m/s · 64.09 km/h | 6,338 m/s² · 646.3 g |
| 10 cm | 20 cm | 35.6 m/s · 128.2 km/h | 12,680 m/s² · 1,293 g |
| 25 cm | 50 cm | 89.01 m/s · 320.4 km/h | 31,690 m/s² · 3,232 g |
| 50 cm | 1 m | 178 m/s · 640.9 km/h | 63,380 m/s² · 6,463 g |
| 1 m | 2 m | 356 m/s · 1,282 km/h | 126,800 m/s² · 12,930 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 3,400 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 56.67 Hz | Reachable with a VFD |
| 4 | 113.3 Hz | Reachable with a VFD |
| 6 | 170 Hz | Above typical VFD range |
| 8 | 226.7 Hz | Above typical VFD range |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 1,133 RPM · 118.7 rad/s | ×3 |
| 5:1 | 680 RPM · 71.21 rad/s | ×5 |
| 10:1 | 340 RPM · 35.6 rad/s | ×10 |
| 30:1 | 113.3 RPM · 11.87 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 63.38 J |
| 0.01 kg·m² (bench-grinder wheel) | 633.8 J |
| 0.1 kg·m² (car flywheel) | 6.338 kJ |
| 1 kg·m² (industrial flywheel) | 63.38 kJ |
Multiples of this speed
- 0.5× = 1,700 RPM178.0236 rad/s
- 2× = 6,800 RPM712.0943 rad/s
- 5× = 17,000 RPM1,780.2358 rad/s
- 10× = 34,000 RPM3,560.4717 rad/s

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 3,400 RPM to radians per second, multiply 3400 by π and divide by 30: 3400 × (π / 30) = 356.047167 rad/s (approx. 356.05 rad/s).
3,400 RPM equals 56.6667 Hz (revolutions per second), calculated by dividing 3400 by 60 seconds.
To convert 356.05 rad/s back to RPM, multiply by 30 and divide by π: 356.05 × (30 / π) ≈ 3,400 RPM.
At 3,400 RPM, one full 360° revolution takes 0.0176 seconds (17.65 ms).
A 4-pole induction motor has a synchronous speed of 3,400 RPM at 113.3333 Hz (f = RPM × poles / 120 = 3400 × 4 / 120). Under load it runs roughly 2–4% below synchronous speed, so a VFD is normally set slightly higher.
Tangential speed is v = ω·r = 356.047167 rad/s × 0.1 m = 35.6047 m/s (128.177 km/h). The centripetal acceleration at the rim is ω²·r = 12676.9585 m/s².