2,800 RPM to Radians Per Second Converter
Instant conversion for 2,800 RPM to rad/s (293.215314 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 293.21531
- Degrees per Second (°/s)
- 16,800 °/s
- Hertz (Hz)
- 46.666667 Hz
- Revolutions per Second (RPS)
- 46.666667 rev/s
- Revolutions per Hour (RPH)
- 168,000 rev/hr
- Revolutions per Day
- 4,032,000 rev/day
- Radians per Minute (rad/min)
- 17,592.919 rad/min
- Milliradians per Second (mrad/s)
- 293,215.31 mrad/s
- Period (seconds per rev)
- 0.021429 s/rev
- Exact Formula
- 2800 × π/30 = 293.21531 rad/s
- Nearest Real-World Example
- Car engine — highway (2,500 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 2,800 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 2800 × (π / 30) = 293.215314 rad/s
Exact fraction: 2800π/30 rad/s · Reciprocal: 293.22 rad/s × (30/π) = 2,800 RPM
Reverse Conversion: 293.22 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
2,800 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
2,800 RPM = 280π/3 rad/s ≈ 293.215314 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 293.16 rad/s instead of the exact 293.2153 rad/s — an error of 0.05531 rad/s.
What this speed looks like in practice
At 2,800 RPM a shaft turns about 1.56× as fast as a 4-pole motor on a 60 Hz grid. A laptop hard drive (5,400 RPM) turns about 1.93× faster.
Revolutions over time
That is 168,000 revolutions per hour and 4,032,000 per day. A quarter turn (90°) takes 5.36 ms, and the shaft sweeps 16.8° every millisecond.
Rim speed and centripetal load at ω = 293.2153 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 2.932 m/s · 10.56 km/h | 859.8 m/s² · 87.67 g |
| 5 cm | 10 cm | 14.66 m/s · 52.78 km/h | 4,299 m/s² · 438.4 g |
| 10 cm | 20 cm | 29.32 m/s · 105.6 km/h | 8,598 m/s² · 876.7 g |
| 25 cm | 50 cm | 73.3 m/s · 263.9 km/h | 21,490 m/s² · 2,192 g |
| 50 cm | 1 m | 146.6 m/s · 527.8 km/h | 42,990 m/s² · 4,384 g |
| 1 m | 2 m | 293.2 m/s · 1,056 km/h | 85,980 m/s² · 8,767 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 2,800 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 46.67 Hz | Reachable with a VFD |
| 4 | 93.33 Hz | Reachable with a VFD |
| 6 | 140 Hz | Above typical VFD range |
| 8 | 186.7 Hz | Above typical VFD range |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 933.3 RPM · 97.74 rad/s | ×3 |
| 5:1 | 560 RPM · 58.64 rad/s | ×5 |
| 10:1 | 280 RPM · 29.32 rad/s | ×10 |
| 30:1 | 93.33 RPM · 9.774 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 42.99 J |
| 0.01 kg·m² (bench-grinder wheel) | 429.9 J |
| 0.1 kg·m² (car flywheel) | 4.299 kJ |
| 1 kg·m² (industrial flywheel) | 42.99 kJ |
Multiples of this speed
- 0.5× = 1,400 RPM146.6077 rad/s
- 2× = 5,600 RPM586.4306 rad/s
- 5× = 14,000 RPM1,466.0766 rad/s
- 10× = 28,000 RPM2,932.1531 rad/s

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 2,800 RPM to radians per second, multiply 2800 by π and divide by 30: 2800 × (π / 30) = 293.215314 rad/s (approx. 293.22 rad/s).
2,800 RPM equals 46.6667 Hz (revolutions per second), calculated by dividing 2800 by 60 seconds.
To convert 293.22 rad/s back to RPM, multiply by 30 and divide by π: 293.22 × (30 / π) ≈ 2,800 RPM.
At 2,800 RPM, one full 360° revolution takes 0.0214 seconds (21.43 ms).
A 4-pole induction motor has a synchronous speed of 2,800 RPM at 93.3333 Hz (f = RPM × poles / 120 = 2800 × 4 / 120). Under load it runs roughly 2–4% below synchronous speed, so a VFD is normally set slightly higher.
Tangential speed is v = ω·r = 293.215314 rad/s × 0.1 m = 29.3215 m/s (105.5575 km/h). The centripetal acceleration at the rim is ω²·r = 8597.5221 m/s².