7,200 RPM to Radians Per Second Converter
Instant conversion for 7,200 RPM to rad/s (753.982237 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.
- Radians per Second (rad/s)
- 753.98224
- Degrees per Second (°/s)
- 43,200 °/s
- Hertz (Hz)
- 120 Hz
- Revolutions per Second (RPS)
- 120 rev/s
- Revolutions per Hour (RPH)
- 432,000 rev/hr
- Revolutions per Day
- 10,368,000 rev/day
- Radians per Minute (rad/min)
- 45,238.934 rad/min
- Milliradians per Second (mrad/s)
- 753,982.24 mrad/s
- Period (seconds per rev)
- 0.008333 s/rev
- Exact Formula
- 7200 × π/30 = 753.98224 rad/s
- Nearest Real-World Example
- Hard drive — high perf (7,200 RPM)
Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:
Worked Conversion: 7,200 RPM to Radians Per Second
To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.
rad/s = 7200 × (π / 30) = 753.982237 rad/s
Exact fraction: 7200π/30 rad/s · Reciprocal: 753.98 rad/s × (30/π) = 7,200 RPM
Reverse Conversion: 753.98 rad/s to RPM
Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.
In-Depth Engineering Guides & References
7,200 RPM: exact form, real-world scale & engineering tables
Exact answer in terms of π
7,200 RPM = 240π rad/s ≈ 753.982237 rad/s
Reduced fraction — keep this form through multi-step problems and only round at the end.
Rounding check
Using the rounded factor 0.1047 gives 753.84 rad/s instead of the exact 753.9822 rad/s — an error of 0.1422 rad/s.
What this speed looks like in practice
That is the typical speed of a desktop hard drive (7,200 RPM). At 7,200 RPM a shaft turns about 1.33× as fast as a laptop hard drive (5,400 RPM). A 115 mm angle grinder turns about 1.53× faster.
Revolutions over time
That is 432,000 revolutions per hour and 10,368,000 per day. A quarter turn (90°) takes 2.08 ms, and the shaft sweeps 43.2° every millisecond.
Rim speed and centripetal load at ω = 753.9822 rad/s
Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.
| Radius | Diameter | Rim speed | Centripetal acceleration |
|---|---|---|---|
| 1 cm | 2 cm | 7.54 m/s · 27.14 km/h | 5,685 m/s² · 579.7 g |
| 5 cm | 10 cm | 37.7 m/s · 135.7 km/h | 28,420 m/s² · 2,898 g |
| 10 cm | 20 cm | 75.4 m/s · 271.4 km/h | 56,850 m/s² · 5,797 g |
| 25 cm | 50 cm | 188.5 m/s · 678.6 km/h | 142,100 m/s² · 14,490 g |
| 50 cm | 1 m | 377 m/s · 1,357 km/h | 284,200 m/s² · 28,980 g |
| 1 m | 2 m | 754 m/s · 2,714 km/h | 568,500 m/s² · 57,970 g |
Driving this speed with an AC motor
Supply frequency an induction motor would need for a synchronous speed of 7,200 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.
| Poles | Supply frequency | Practical note |
|---|---|---|
| 2 | 120 Hz | Reachable with a VFD |
| 4 | 240 Hz | Above typical VFD range |
| 6 | 360 Hz | Above typical VFD range |
| 8 | 480 Hz | Above typical VFD range |
Through a reduction gearbox
Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.
| Ratio | Output speed | Torque × |
|---|---|---|
| 3:1 | 2,400 RPM · 251.3 rad/s | ×3 |
| 5:1 | 1,440 RPM · 150.8 rad/s | ×5 |
| 10:1 | 720 RPM · 75.4 rad/s | ×10 |
| 30:1 | 240 RPM · 25.13 rad/s | ×30 |
Stored rotational energy
Kinetic energy E = ½·I·ω² for a range of moments of inertia.
| Moment of inertia | Energy |
|---|---|
| 0.001 kg·m² (small fan impeller) | 284.2 J |
| 0.01 kg·m² (bench-grinder wheel) | 2.842 kJ |
| 0.1 kg·m² (car flywheel) | 28.42 kJ |
| 1 kg·m² (industrial flywheel) | 284.2 kJ |
Multiples of this speed
- 0.5× = 3,600 RPM376.9911 rad/s
- 2× = 14,400 RPM1,507.9645 rad/s
- 5× = 36,000 RPM3,769.9112 rad/s
- 10× = 72,000 RPM7,539.8224 rad/s

Rizwan Malik
Founder & Editor
- Formulas checked against the BIPM SI Brochure
- Unit definitions per NIST SP 811
Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.
Frequently asked questions
To convert 7,200 RPM to radians per second, multiply 7200 by π and divide by 30: 7200 × (π / 30) = 753.982237 rad/s (approx. 753.98 rad/s).
7,200 RPM equals 120.0000 Hz (revolutions per second), calculated by dividing 7200 by 60 seconds.
To convert 753.98 rad/s back to RPM, multiply by 30 and divide by π: 753.98 × (30 / π) ≈ 7,200 RPM.
At 7,200 RPM, one full 360° revolution takes 0.0083 seconds (8.33 ms).
A 4-pole induction motor has a synchronous speed of 7,200 RPM at 240 Hz (f = RPM × poles / 120 = 7200 × 4 / 120). That is beyond a standard motor and drive, so this speed calls for a high-speed spindle motor or a step-up transmission.
Tangential speed is v = ω·r = 753.982237 rad/s × 0.1 m = 75.3982 m/s (271.4336 km/h). The centripetal acceleration at the rim is ω²·r = 56848.9214 m/s².