RPM to Radians Per SecondRPM to rad/s

4,500 RPM to Radians Per Second Converter

Instant conversion for 4,500 RPM to rad/s (471.238898 rad/s). Analytical π/30 formula, rotational frequency in Hz, and full kinematics.

m
Result471.238898 rad/s
Radians per Second (rad/s)
471.2389
Degrees per Second (°/s)
27,000 °/s
Hertz (Hz)
75 Hz
Revolutions per Second (RPS)
75 rev/s
Revolutions per Hour (RPH)
270,000 rev/hr
Revolutions per Day
6,480,000 rev/day
Radians per Minute (rad/min)
28,274.334 rad/min
Milliradians per Second (mrad/s)
471,238.9 mrad/s
Period (seconds per rev)
0.013333 s/rev
Exact Formula
4500 × π/30 = 471.2389 rad/s
Nearest Real-World Example
Hard drive (5,400 RPM)
Precision Drift Meter (Exact π/30 vs. 0.10472 Rounded)Zero Drift Here

Generic web calculators use the rounded 0.10472 multiplier. At this rotational speed, that approximation introduces numerical drift:

Exact Value (π/30):471.238898 rad/s
Rounded (0.10472):471.240000 rad/s
Angular Error / Hour:227.30° / hr

Worked Conversion: 4,500 RPM to Radians Per Second

To convert revolutions per minute (RPM) to SI angular velocity (rad/s), multiply by 2π radians per revolution and divide by 60 seconds per minute. The analytical factor simplifies to π/30.

rad/s = 4500 × (π / 30) = 471.238898 rad/s

Exact fraction: 4500π/30 rad/s · Reciprocal: 471.24 rad/s × (30/π) = 4,500 RPM

Angular Velocity
471.238898 rad/s
Frequency
75 Hz
Degrees / Second
27,000 °/s
Period per Rev
0.0133 s
Engineering Context: Several thousand RPM is power-tool and high-revving-engine territory, where balance and bearing life become the binding constraints.

Reverse Conversion: 471.24 rad/s to RPM

Need to convert from radians per second back to RPM? Use our reverse programmatic converter with exact 30/π precision.

Browse Reverse Conversions →

In-Depth Engineering Guides & References

5.36 Rad/s to RPM: College Physics Homework Benchmark Solution— Serway & Halliday kinematics proof and analytical derivation.
RPM to Radians Per Second Formula & Calculus Proof— Dimensional cancellation, π/30 derivation, and IEEE 754 precision.
Angular Velocity Guide & Rotational Kinematics— SI standards, tangential velocity (v = ω·r), and centripetal acceleration.
Complete Conversion Index— Browse pre-calculated conversion speeds from 1 to 20,000 RPM.

4,500 RPM: exact form, real-world scale & engineering tables

Exact answer in terms of π

4,500 RPM = 150π rad/s ≈ 471.238898 rad/s

Reduced fraction — keep this form through multi-step problems and only round at the end.

Rounding check

Using the rounded factor 0.1047 gives 471.15 rad/s instead of the exact 471.2389 rad/s — an error of 0.0889 rad/s.

What this speed looks like in practice

At 4,500 RPM a shaft turns about 2.5× as fast as a 4-pole motor on a 60 Hz grid. A laptop hard drive (5,400 RPM) turns about 1.2× faster.

Revolutions over time

That is 270,000 revolutions per hour and 6,480,000 per day. A quarter turn (90°) takes 3.33 ms, and the shaft sweeps 27° every millisecond.

Rim speed and centripetal load at ω = 471.2389 rad/s

Tangential speed v = ω·r and centripetal acceleration a = ω²·r for common radii.

RadiusDiameterRim speedCentripetal acceleration
1 cm2 cm4.712 m/s · 16.96 km/h2,221 m/s² · 226.4 g
5 cm10 cm23.56 m/s · 84.82 km/h11,100 m/s² · 1,132 g
10 cm20 cm47.12 m/s · 169.6 km/h22,210 m/s² · 2,264 g
25 cm50 cm117.8 m/s · 424.1 km/h55,520 m/s² · 5,661 g
50 cm1 m235.6 m/s · 848.2 km/h111,000 m/s² · 11,320 g
1 m2 m471.2 m/s · 1,696 km/h222,100 m/s² · 22,640 g

Driving this speed with an AC motor

Supply frequency an induction motor would need for a synchronous speed of 4,500 RPM (f = RPM × poles / 120). Real motors run 2–4% below synchronous speed under load.

PolesSupply frequencyPractical note
275 HzReachable with a VFD
4150 HzAbove typical VFD range
6225 HzAbove typical VFD range
8300 HzAbove typical VFD range

Through a reduction gearbox

Output speed and ideal torque multiplication (losses ignored) for common reduction ratios.

RatioOutput speedTorque ×
3:11,500 RPM · 157.1 rad/s×3
5:1900 RPM · 94.25 rad/s×5
10:1450 RPM · 47.12 rad/s×10
30:1150 RPM · 15.71 rad/s×30

Stored rotational energy

Kinetic energy E = ½·I·ω² for a range of moments of inertia.

Moment of inertiaEnergy
0.001 kg·m² (small fan impeller)111 J
0.01 kg·m² (bench-grinder wheel)1.11 kJ
0.1 kg·m² (car flywheel)11.1 kJ
1 kg·m² (industrial flywheel)111 kJ

Multiples of this speed

Rizwan Malik headshot

Rizwan Malik

Founder & Editor

  • Formulas checked against the BIPM SI Brochure
  • Unit definitions per NIST SP 811

Rizwan Malik builds and maintains RPM to Radians Per Second. Every formula, table and worked example on the site is checked against the BIPM SI Brochure and NIST unit guidance before it is published.

Frequently asked questions